House of Calculator

Updated 27 January 2027 · By the House of Calculator team

To work out how many tiles you need, multiply the length by the width of the area to get its size, divide by the area of one tile including its grout gap, then add 10% for cuts and breakages (15% for diagonal or patterned layouts) and round up to whole boxes. A 3.2 m by 2.4 m bathroom floor with 60 cm by 30 cm tiles needs about 47 tiles, which is 8 boxes if each box holds 6.

The basic method in four steps

Every tiling job uses the same sums, whether it is a floor, a wall or a splashback.

  1. Measure the area to be tiled in metres (or feet), as length times width.
  2. Work out the area of one tile, including half of the grout gap on each side. In practice that means adding the gap to both tile dimensions.
  3. Divide the area by the tile area to get the number of tiles with no waste.
  4. Add an allowance for waste, then round up to full boxes, because tiles are sold in packs.

The result is a purchase number, not just a count. You should never buy exactly what the sums say, because tiles break, cuts do not always reuse the offcuts, and walls are never perfectly square.

Measuring the area

Measure each wall or floor section with a tape, at the widest and longest points, because few rooms are truly rectangular. Write the dimensions down and sketch the shape.

  • Rectangular areas: length × width. A 3.2 m × 2.4 m floor is 7.68 m².
  • L-shaped or awkward rooms: split into rectangles, work out each, and add them.
  • Walls: measure the height you will tile to, and the length of each wall, then multiply. Add the walls together.
  • Subtract openings: take away doors, windows and any large fixed items that will not be tiled, such as a bath panel. For small gaps (a radiator pipe, a switch) there is no need, as the waste allowance covers them.
  • Mixed areas: if you are tiling a floor and walls, work out each separately, because you may use different tiles.

Measure twice, and measure to the point where the tile will stop, not to the paint line. How to measure for flooring and fencing explains how to measure awkward spaces, and How much paint, wallpaper or tile do you need? covers the area sums for other finishes.

Allow for the grout gap

Tiles sit slightly apart, with a grout line between them. A gap of 2 to 3 mm is typical for wall tiles and larger gaps are used on floors and rustic styles, but follow the tile maker’s recommendation. The gap matters more with small tiles, because there are more joints per square metre.

On a 60 cm × 30 cm tile with a 3 mm joint, the effective size is 603 mm × 303 mm. That is an area of 0.1827 m² rather than 0.18 m². On a floor of 7.68 m² the unadjusted sum gives about 42.7 tiles, while the sum with the gap gives about 42.0. The difference is under one tile here, but it grows quickly with mosaics. For a 10 cm mosaic tile, a 2 mm gap changes the count by around 4%.

The House of Calculator tile tool includes the gap as an input, so you do not need to adjust by hand.

How much waste to add

The waste allowance covers cut tiles that cannot be reused, breakage, mistakes and pattern matching. Typical guidance, in line with common trade practice, is:

Layout Suggested waste
Straight (grid) layout, simple room about 10%
Brick bond, offset or irregular rooms about 10 to 15%
Diagonal layout about 15%
Herringbone or complex patterns 15% or more, check with your supplier
Large-format tiles in a small room often 10 to 15%, because cuts waste more

Also think about the future. Tile ranges are discontinued, and batches differ in shade. Many people buy an extra box to keep for repairs, which is worth considering for a floor or a feature wall. Check batch (or shade) numbers on the boxes when you buy and use tiles from the same batch.

Worked example 1: a bathroom floor

A bathroom floor measures 3.2 m by 2.4 m. The tiles are 60 cm × 30 cm, laid straight with a 3 mm gap, and sold in boxes of 6. Using the tile calculator:

  • Area: 3.2 × 2.4 = 7.68 m²
  • Tiles needed with no waste: 43 (rounded up from 42.03)
  • With 10% waste: 47 tiles
  • Boxes to buy: 8 (48 tiles)

If you chose a diagonal layout with 15% waste, the answer is 49 tiles, so you would need 9 boxes (54 tiles). One layout choice changes the order by a whole box.

Each tile covers 0.18 m², so six tiles cover 1.08 m² and 8 boxes cover 8.64 m². That is 0.96 m² more than the floor, which is the waste you have paid for.

Worked example 2: a kitchen splashback or feature wall

A wall to be tiled measures 2.4 m wide by 1.8 m high, with 30 cm × 30 cm tiles in boxes of 11.

  • Area: 2.4 × 1.8 = 4.32 m²
  • With a 3 mm gap, no waste: 48 tiles
  • With 10% waste: 52 tiles, so 5 boxes (55 tiles)
  • With 15% waste: 55 tiles, which is exactly 5 boxes

Here both waste levels lead to 5 boxes, so you would buy 5 and have three spare tiles at the 10% level. Because a box of 11 does not divide neatly, check that the number you need does not sit right on the edge of a box.

Worked example 3: comparing tile sizes on a 4 m by 3 m floor

The same 12 m² floor takes very different quantities depending on the tile:

Tile size Gap Waste Tiles needed Box size Boxes
45 × 45 cm 3 mm 10% 65 5 13
120 × 60 cm 2 mm 10% 19 2 10

The large-format tiles give fewer joints and a cleaner look, but each tile is heavy and costs more to cut and lay, and large tiles need a flat floor. Always check how the cost per square metre compares, and not just the number of tiles. Boxes show the area covered, so dividing your area by the box coverage and adding waste is another way to check the sum.

Planning the layout to avoid thin cuts

Counting tiles is only half the job. A poor layout leaves thin slivers at the edges that look untidy and are hard to cut. Plan the layout before buying adhesive.

For the 3.2 m side of the bathroom floor above, with 60 cm tiles on a 603 mm pitch (including the gap):

  • Five full tiles plus two edge cuts would leave cuts of just 92.5 mm each, which is too narrow.
  • Four full tiles with two edge cuts would give cuts of 394 mm each, which is much better.

The rule of thumb is to start in the middle of the room or the focal wall and work outwards, so that cuts at both ends are balanced and at least half a tile wide. Dry-lay a row of tiles, with spacers, before you fix anything. The calculator gives you the quantity; the layout decides how well it looks.

Working in feet and inches, and checking against box coverage

If you measure in feet, convert at the end rather than midway: one square metre is about 10.76 square feet, so the 7.68 m² bathroom floor is about 82.7 square feet, which is the figure the calculator shows alongside the metric one. Most UK tile boxes state the coverage in square metres, so converting your area to metres lets you compare directly.

A useful cross-check is box coverage. If a box covers 1.08 m² and your floor is 7.68 m², you need 7.68 ÷ 1.08 = 7.1 boxes before any waste, and with 10% waste about 7.8, which rounds up to 8 boxes. That matches the tile count, and if the two methods disagree, recheck your measurements before you order.

Other materials to order

The tile count is the headline number, but the job needs more:

  • Adhesive and grout. Coverage depends on the product, the tile size and the trowel notch depth, so use the figure on the packaging for your area.
  • Spacers, trims and edging. Count the metres of edge that need a trim.
  • Primer or levelling compound if the surface is uneven.
  • Sealant for corners and around baths and sinks.
  • Cutting tools, or hire them. A tile cutter or wet saw makes a big difference to the finish.

For a floor, check with a flooring specialist that the substrate is suitable and any necessary preparation is done. Waterproofing is important in wet areas.

Common mistakes

  • Forgetting to round up to whole boxes. Tiles are not sold individually in most cases.
  • Using the wrong waste figure for the layout. Diagonal work needs more.
  • Ignoring the grout gap on small tiles.
  • Measuring from the wrong point, such as to the skirting rather than where the tile ends.
  • Buying exactly enough. A single broken tile can leave you stuck, and a later batch may not match.
  • Mixing batches. Check shade numbers.
  • Not subtracting large openings, such as a big window on a wall tiled floor to ceiling.

Try the calculator

Enter the length and width of your area, the tile size, the grout gap, your waste allowance and the number of tiles in a box into the Tile Calculator. It shows the area, tiles with and without waste, and how many boxes to buy.

Frequently asked questions

How many tiles do I need per square metre?

Divide 1 by the area of one tile in square metres, including the gap. A 30 cm × 30 cm tile covers 0.09 m², so you need about 11 per square metre, before waste.

How much extra should I order?

About 10% for a straight layout and about 15% for diagonal or patterned layouts. Complex patterns, awkward rooms and large tiles can need more.

Should I buy a spare box?

It is a good idea, especially for floors. Ranges are discontinued and later batches may differ in shade, so a spare box lets you replace a damaged tile.

Do I count the grout gap?

Yes, particularly for small tiles. The gap adds a little to the effective size of each tile, so it slightly reduces how many you need.

How many tiles are in a box?

It varies by size and manufacturer. Check the box label for the number of tiles and the area it covers, then round your total up to whole boxes.

Related calculators

More guides